Episode 679
Planar transmission line
Fri, 2019-Mar-15 01:45 UTC
Length - 5:03
Direct Link
Welcome to featured Wiki of the Day where we read the summary of the featured Wikipedia article every day.
The featured article for Friday, 15 March 2019 is Planar transmission line.
Planar transmission lines are transmission lines with conductors, or in some cases dielectric (insulating) strips, that are flat, ribbon-shaped lines. They are used to interconnect components on printed circuits and integrated circuits working at microwave frequencies because the planar type fits in well with the manufacturing methods for these components. Transmission lines are more than simply interconnections. With simple interconnections the propagation of the electromagnetic wave along the wire is fast enough to be considered instantaneous, and the voltages at each end of the wire can be considered identical. If the wire is longer than a large fraction of a wavelength (one tenth is often used as a rule of thumb) these assumptions are no longer true and transmission line theory must be used instead. With transmission lines, the geometry of the line is precisely controlled (in most cases, the cross-section is kept constant along the length) so that its electrical behaviour is highly predictable. At lower frequencies, these considerations are only necessary for the cables connecting different pieces of equipment, but at microwave frequencies the distance at which transmission line theory becomes necessary is measured in millimetres. Hence, transmission lines are needed within circuits.
The earliest type of planar transmission line was conceived during World War II by Robert M. Barrett. It is known as stripline, and is one of the four main types in modern use, along with microstrip, suspended stripline, and coplanar waveguide. All four of these types consist of a pair of conductors (although in three of them, one of these conductors is the ground plane). Consequently, they have a dominant mode of transmission (the mode is the field pattern of the electromagnetic wave) that is identical, or near-identical, to the mode found in a pair of wires. Other planar types of transmission line, such as slotline, finline, and imageline, transmit along a strip of dielectric, and substrate integrated waveguide forms a dielectric waveguide within the substrate with rows of posts. These types cannot support the same mode as a pair of wires, and consequently they have different transmission properties. Many of these types have a narrower bandwidth and in general produce more signal distortion than pairs of conductors. Their advantages depend on the exact types being compared, but can include low loss and a better range of characteristic impedance.
Planar transmission lines can be used for constructing components as well as interconnecting them. At microwave frequencies it is often the case that individual components in a circuit are themselves larger than a significant fraction of a wavelength. This means they can no longer be treated as lumped components, that is, treated as if they existed at a single point. Lumped passive components are often impractical at microwave frequencies, either for this reason, or because the values required are impractically small to manufacture. A pattern of transmission lines can be used for the same function as these components. Whole circuits, called distributed element circuits, can be built this way. The method is often used for filters. This method is particularly appealing for use with printed and integrated circuits because these structures can be manufactured with the same processes as the rest of the assembly simply by applying patterns to the existing substrate. This gives the planar technologies a big economic advantage over other types, such as coaxial line.
Some authors make a distinction between transmission line, a line that uses a pair of conductors, and waveguide, a line that either does not use conductors at all, or just uses one conductor to constrain the wave in the dielectric. Others use the terms synonymously. This article includes both kinds, so long as they are in a planar form. Names used are the common ones and do not necessarily indicate the number of conductors. The term waveguide when used unadorned, means the hollow, or dielectric filled, metal kind of waveguide, which is not a planar form.
This recording reflects the Wikipedia text as of 01:45 UTC on Friday, 15 March 2019.
For the full current version of the article, see Planar transmission line on Wikipedia.
This podcast is produced by Abulsme Productions based on Wikipedia content and is released under a Creative Commons Attribution-ShareAlike License.
Visit wikioftheday.com for our archives, sister podcasts, and swag. Please subscribe to never miss an episode. You can also follow @WotDpod on Twitter.
Abulsme Productions produces the current events podcast Curmudgeon's Corner as well. Check it out in your podcast player of choice.
This has been Geraint. Thank you for listening to featured Wiki of the Day.
|
|
Buy WotD Stuff!!
